AVI SCIENCE TECHNOLOGY AND INNOVATION SERIES

Welding Technology for Tubular Busbars

Welding Technology for Tubular Busbars

Tungsten Inert Gas (TIG) welding, or Gas Tungsten Arc Welding (GTAW), is preferred for welding copper busbars because of its precision and control. Weld your busbars with ultrasonics to permanently benefit from strong connections without contact resistance — even with different metals like aluminum and copper. Discover the benefits of our innovative welding technology for more output, control, and efficiency in your production! to 12 s per. Although the technology behind electric vehicles (EVs) has been around for some time, the last decade as has seen a significant increase in the sale of EVs and hybrid electric vehicles (HEVs) as private motor vehicles. Especially in the manufacture of busbars, which are used in power distribution systems, electric vehicles and other high-current-carrying applications, choosing the right joining technology is crucial for. Busbars are flat conductors that are becoming part of the architecture of electric vehicles. Busbars are typically installed inside switchgear, distribution boards, and busway enclosures for localized high-current power distribution.

Read More
Fiber Optic Sensing Technology brullouin

Fiber Optic Sensing Technology brullouin

Brillouin Distributed Optical Fibre Sensing (Brillouin D-FOS) is a powerful lightwave technology for measuring and mapping temperatures, deformations and pressures in thousands of industrial, civil and environmental applications. Brillouin scattering in optical fiber describes the interaction of an electro-magnetic field (photon) with a characteristic density variation of the fiber. When the electric field amplitude of an optical beam (so-called pump wave), and another wave is introduced at the downshifted Brillouin. This chapter provides an overview of different Brillouin sensing techniques and mainly focuses on the most widely used one, the Brillouin optical time domain analysis (BOTDA). Techniques have been developed to monitor temperature, strain, and vibration over distances of more than 50.

Read More
Relay Protection Technology Q

Relay Protection Technology Q

Electromechanical relays can be classified into several different types as follows: "Armature"-type relays have a pivoted lever supported on a hinge or knife-edge pivot, which carries a moving contact. These relays may work on either alternating or direct current, but for alternating current, a shading coil on the pole is used to maintain contact force throughout the alternating current cycle. This paper presents a chip-based relay protection technology based on system-on-chip (SoC), which is described from four aspects, namely, the architectural design of the relay protection SoC, software and hardware cooperative relay protection based on the SoC IP core . IEEE/IAS/I&CPSD Protection & Coordination WG Chair Jacobs Canada, Calgary, AB rasheek. com IEEE Southern Alberta Section PES/IAS Joint Chapter Technical Seminar - November 2016 Protective Relays - Technical Seminar Nov 2016 - Copyright: IEEE 2 Abstract: Protective relays and devices. These clean energy sources, connected through inverters and flexible transmission systems, are transforming traditional grids based on synchronous generators into more flexibl cant challenges to system stability. Long term cost reduction (TCO) for trainings and maintenance by reduce variety of relays A fast and selective arc fault mitigation for air-insulated LV & MV switchgear and Relion protection and control relays and sensor technology protect staff and plant facilities for many years.

Read More
Malta Joins Silicon Photonics Technology 40G

Malta Joins Silicon Photonics Technology 40G

Under the new agreement, Silicon Labs' future wireless system-on-chips (SoCs) will be produced at GF's advanced fabrication facility in Malta, New York, using the foundry's new 40nm Ultra Low Power (40ULP-ESF3) platform. SCALE CPO solution is the industry's first OCI MSA capable platform and built with GF's proven silicon photonics technology MALTA, N. , May 4, 2026 – GlobalFoundries (Nasdaq: GFS) (GF) today announced the introduction [. Department of Commerce has increased subsidies for advanced packaging technologies. GlobalFoundries of Malta, NY, (GF, the only US-based pure-play foundry with a global manufacturing footprint including facilities in the USA, Europe and Singapore) plans to invest another $3bn in its expansion of semiconductor manufacturing and advanced packaging capabilities across its facilities. Minister for the Economy, Enterprise and Strategic Projects, Silvio Schembri, today attended the Competitiveness Council in Brussels, where he underlined Malta's strong commitment to enhancing Europe's competitiveness, technological leadership, and digital transition.

Read More

Get In Touch

Connect With Us

📧

Email

[email protected]

📱

Spain (Sales & Engineering HQ)

+34 910 257 483

📍

Headquarters & Manufacturing

Calle de la Innovación 22, 28043 Madrid, Spain